yes we are 120v here. I tried to turn on monitor with out power. I had forgot to plug the monitor into the wall
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Hershey
Monitor arrived today in an orginal box!!!! It is in almost mint condition Very clean condition. woot!
Plugged in computer cables and powered up monitor no picture. Pushed power button still no picture
Silly me try plugging it into the wall. Works great now. It seem the 1084 monitors need 120v to Work
Silly me Silly Hershey
You do not say if you have a ramlink connected with the parallel hook up cable. If you do you need to turn off the parallel access using @P0 then run the hd configure program. to turn it on again @p1 or just reset computer. page 2.7 in the ram link manual under hd parallel hook up. Rather hard to find in manuals because it is not in the hard drive manual
Does anyone have a copy of LADS for the C-128? It is a assembler/disassembler for the C-128.you can find lads here
and book here
I have commander 128 (after a few years I thought i would try it out)
The 64 verison worked fine on my 100meg hd.
I upgraded to 4g drive and the add drive program does not add the cd-rom drive (it knows it is there)
the 100meg drives partition was maxed out, The 4g drive is not even close. Does it have to be fully partitioned for the adddrive progran to ad the cd-rom?
Could it also be why when I just use the file name, the bbs never finish loading just sits there with the ra drive light on and I have to reset the system and use load"dragondire bbs",8 to load up the bbs boot file
Ok i read the manual over and over and the only thing I can find is
Any legal filename typed beginning in the first column of the screen will cause the system to attempt to load and execute that file. The INVOKE feature works for both BASIC and machine language programs. Simply type the program's name, followed by a carriage return.
am I missing somthing - a full manual maybe.
« on: January 16, 2011, 10:43 AM »
Try out this windows program Works with all cbm basics
Edit Commodore Basic files on the PC with syntax highlighting and support of the full PETSCII character set
can also save files as pc text file
Full review here
Thanks for the quick rely BigDumbDinosaur
I do understand about not following proper programing and I was hoping it was not that. Will move bbs back to cmd hard drive. Could it also be why when I just use the file name, the bbs never finish loading just sits there with the ra drive light on and I have to reset the system and use load"dragondire bbs",8 to load up the bbs boot file
I Just installed the ra this weekend. It is working great. very fast. little ticked with the manuals for the fact it mentioned that you could boot into 128 mode but did not state how it was done. So after many time going over manuals and online search I gave up and went to the configure software. Very power software. After playing around in there (carefull not to change anything that I could not remember what it was before) found lots of features and the c128 mode boot. now I moved dragonfire bbs software to it (went well except rel file, had to use a rel file copier)
Now to run the bbs software - did not load with dragonfire bbs had to use load"dragonfire bbs",8 and was loaded before I could remove my hand from keyboard.
typed run then this happend
when I exited ml monitor the ra display bar came up under the load dragonfire prompt.
removed the ? at the end of the load command and the bbs loaded and ran fine.
this well cause a problem because this software loads in stand alone modules moving back in forth I would have to be there to run the mods and main bbs prg. if the bbs loads a prg that I wrote it will not load it but will return back to the bbs after I load it (I use load"dragonfire ?.?",dv:run).
my question is is the ra bar interfering with the direct mode input of commands if so how do I turn off display bar with out turing of ra
Where can I find this book ?
Abacus Commodore 128: Basic 7.0 Internals Book 2
Have looked around the net, with no luck.
Found books 1 to 8 except for 2
A pdf would be fine. Would like to have paperback as well to help compleate my collection
Thanks for the replies.
Now I know the code works in other vice systems.
Tried the code on my desktop and got the same responce, also tried wte's code and it stopped too, at the end of prg no ready prompt. Which leaves me wondering what setting in vice I have to Change?
I just ran the code in vice c64 and it worked correctly. Now I really have to check setting in vice 128
This program hangs at line 70 in winvice c128, except if you turn on tron , then it works or if you put in a print d command in side loop (line 70)
Have not tried it on a real c128 yet
20 PRINT CHR$(147)
30 PRINT "DEVICE NUMBER CHECK": PRINT
40 DN=PEEK(186):PRINT "DEVICE NUMBER";DN;":ACCESSED LAST":PRINT
50 FOR DV=8 TO 15:OPEN 1,DV,15:CLOSE 1
60 PRINT"DEVICE NUMBER";DV;": ";:A$="NOT PRESENT":IF ST<0 THEN 90
70 OPEN1,DV,15,"UJ":FOR D= 1 TO 1000:NEXT:INPUT#1,A,A$:CLOSE1
80 A$=RIGHT$(A$,4):IF LEFT$(A$,1)<>"1" THEN A$="DRIVE UNKNOWN"
90 PRINT A$:NEXT
Try it out see if it works for you
Hi, all, I was just wondering if anybody knew the status of TPUG? I sent an order in for their store a week ago and have not heard back. I am wondering if anyone is still answering the e-mail.
I sent in my membership and orderd their new tpug dvd. Which arrived last week. but it had a flaw on the disk, They are sending me a new one.
I Will look around for the disk or the information.
Here is what I found on the net
It is commodore's version (I think)
attached is the cpm .d81 format
Years ago I had modified the cpm 3.0 boot disk to handle a 1581 drive. It worked great. It also booted cpm. The only problem was you had to format the disks in 128 mode with a utility (1581 utility disk, I think). For cpm format program did not support 1581 format. Over time I have misplaced the information (I think it was in a magazine) I may still have the disk. If I Did not use it for another purpose.
Looking for c64 BBS software called The Stock Exchange(TSE). It is a BBS with a message base and Stock Market built right in to the main bbs code so stock prices are updated at all times not just when the game loads.
Originally developed by a Canadian company called Telepro Techologies.
More info Here http://www.bbsdocumentary.com/software/COMMODORE/AMIGA/DLG/
Does anybody have .d64 images of this? I don't have mine anymore, I accidentally lost them while moving files around. :-(
Try again with this new link http://elitebbs.dyndns.org:8000/mag/
made a little change to the address
Main link to all files has also changed to http://elitebbs.dyndns.org:8000
In vice turn off the true drive emulation and the program will run.
So where can you download Wheels then?
ftp://ftp.scs-trc.net/pub/c64/Tools/GEOS wheels_128_1999_Maurice_Randell.zip 113.414
ftp://ftp.scs-trc.net/pub/c64/Tools/GEOS wheels_64_1999_Click_Here_Software.zip 381.686
ftp://ftp.scs-trc.net/pub/c64/Tools/GEOS wheels_64_1999_Maurice_Rand.zip 81.143